Table of Contents
- 1 What AFI establishes procedures to be used for airfield driving at Barksdale AFB?
- 2 What defines the controlled movement area?
- 3 What marking is used to differentiate between the movement and non-movement areas?
- 4 What does a VFR hold line look like?
- 5 What does the non-movement area include?
- 6 What is the non-movement area?
- 7 What is the color of taxiway lights?
- 8 What does L and R mean on runways?
- 9 What is a controlled movement area ( CMA ) violation?
- 10 Where are vehicles not allowed on an airfield?
- 11 How are ” heavies ” parked at an airfield?
What AFI establishes procedures to be used for airfield driving at Barksdale AFB?
By order of the Secretary of the Air Force (SecAF), Air Force Instruction (AFI) 13-213, Airfield Driving, is re-designated Department of the Air Force (DAF) Instruction (DAFI) 13-213, and this DAF Guidance Memorandum (DAFGM) immediately implements changes to DAFI 13- 213. Compliance with this Memorandum is mandatory.
What defines the controlled movement area?
The Controlled Movement Area is any portion of the airfield requiring aircraft, vehicles and pedestrians to obtain specific Air Traffic Control approval for access. The penalties for airfield violations will result in the individual immediately losing his or her airfield driving privileges.
When entering the airfield vehicle operators must perform which of the following?
|When entering the airfield, vehicle operators must perform which of the following||All the above|
|What are the leading causes of runway incursions||All the above|
|Before entering the controller area l, vehicle operators must do which of the following||All the above|
What marking is used to differentiate between the movement and non-movement areas?
A single solid line along with single dashed yellow lines, this marking divides the movement and non-movement areas on the airfield. When you are positioned on the solid line side of the marking, or the non-movement area, ATC clearance is required for you to drive across into the movement area. markings.
What does a VFR hold line look like?
A hold line is painted on a taxiway and applies to VFR and IFR traffic. It consists of a double yellow line and a double broken yellow line.
Are identified by numbers that represent the orientation?
Runways are identified how? By numbers that rep the orientation of the runway approach in compass degrees rounded to the nearest 10. Parallel runways will have the letters L for left, R for right as viewed from the cockpit of aircraft landing or taking off.
What does the non-movement area include?
The Non-Movement Area (NMA) includes the Terminal, Cargo, and General Aviation Ramps along with associated service roads. Taxilanes are designed for low speed and precise taxiing of aircraft, providing access from MA taxiways to aircraft parking positions and other terminal areas.
What is the non-movement area?
Non-movement Areas–the area, other than that described as the movement area, used for the loading, unloading, parking, and movement of aircraft on the airside of the airport (including apron areas and on airport fuel farms). 2.17. Operator–any person who is in actual physical control of an aircraft or a motor vehicle.
What is the VFR hold line marking used for?
Holding Position Markings on Taxiways Located in Runway Approach Areas. These markings are used at some airports where it is necessary to hold an aircraft on a taxiway located in the approach or departure area of a runway so that the aircraft does not interfere with the operations on that runway.
What is the color of taxiway lights?
Taxiway edge lights are used to outline the edges of taxiways during periods of darkness or restricted visibility conditions. These fixtures emit blue light. At most major airports these lights have variable intensity settings and may be adjusted at pilot request or when deemed necessary by the controller.
What does L and R mean on runways?
The ”L” and ”R” designate the relative position (left or right) of each runway respectively when approaching/facing its direction. A small number of airports have three parallel runways—the runway in the middle gets a “C” for center.
What is a hold short line?
Hold-Short Of Approach Areas When Instructed According to the FAA’s AIM 2-3-5, “when specifically instructed by ATC, ‘Hold short of Runway XX approach or Runway XX departure area,’ the pilot MUST STOP so that no part of the aircraft extends beyond the holding position marking.”
What is a controlled movement area ( CMA ) violation?
A controlled movement area (CMA) violation that is a result of an unauthorized entry or erroneous occupation of a runway or other surface used for takeoff and landing of aircraft, regardless of impact on aircraft safety. Runway incursion What must you have to be an escort or part of a convoy?
Where are vehicles not allowed on an airfield?
Vehicles are prohibited within the Circle of Safety, a circular area extending _____ ft beyond the wing tips, nose, and tail of an aircraft (except when the vehicle is used to service an aircraft). 25 All vehicles must approach parked aircraft…
How should vehicles approach an aircraft at an airfield?
A. Unit Commanders B. Airfield Driving Program Managers C. Airfield Management ⭐️ D. All of the above No vehicles will be driven within __ feet of fueling/refueling operations unless specifically authorized by a directive. 50 feet Taxiway locations signs have yellow inscriptions on a black background? True How should vehicles approach an aircraft?
How are ” heavies ” parked at an airfield?
Identify who you’re calling, identitify yourself/location, communicate specific info, acknowledge understanding of towers instruction by repeating back verbatim the towers instructions. How are “Heavies” parked?