How do I reset my Jeep Laredo?

How do I reset my Jeep Laredo?

How to Reset the Jeep Grand Cherokee Service Required Message

1. Turn the ignition switch to the “ON” position without starting the vehicle.
2. Press the gas pedal to the floor slowly three times within 10 seconds.
3. Turn the ignition off. Wait 10 seconds and start the engine.

How do you reset a Jeep Grand Cherokee computer?

How do I reset my Jeep Cherokee computer?

1. Disconnect the battery by removing the positive battery cable.
2. Ground the positive cable to the negative cable for 30 seconds to erase the electric charge in the capacitors.
3. Reconnect the positive cable to the battery.
4. Turn the key to on but do not start.
5. Turn the headlights on.

How do you reset an ignition lock cylinder?

How to Program an Ignition Switch

1. Enter your car with your cut ignition key and insert the key into the ignition switch.
2. Turn the key to the “On” position and leave it in that position for 10 minutes and 30 seconds.
3. Turn the car back to the “Off” position within 45 seconds of the 10:30 elapsing.

How do you program the ignition switch on a Jeep Grand Cherokee?

Put the first preprogrammed key into the car’s ignition and turn it to “On.” This is the farthest you can turn the key before you start up your car’s motor. Turn the key back to “Off” after five seconds have passed. Repeat Step 2, but this time use the second preprogrammed key.

What would cause a Jeep Cherokee to not start?

The most common causes that hinders normal starting operation of your Grand Cherokee are dead key fob battery, dead 12v battery, corrosion on battery terminals, bad alternator, clogged fuel filter, broken starter, blown fuse, empty gas tank, immobilizer error or any fault in the electrical system.

How do you reset the transmission on a Jeep Grand Cherokee?

Reset Automatic Transmission Adaptation

1. Press the gas pedal down and keep it pressed.
2. Turn ignition on without starting the engine.
3. Keep ignition on (engine off) and the gas pedal pressed for 30 seconds.
4. Turn the ignition off.
5. Release the gas pedal.

How long does battery need to be disconnected to reset ECU?

Disconnecting the battery for a short time may not do the trick because the car’s computer, or ECU, still has some current in it. Waiting for over 15 minutes after disconnecting the engine will help ensure the equipment is reset.

How do I find my ignition code?

Finding the key code

1. In the documentation of the vehicle. Sometimes the key code is in the vehicle manual or on a label with the lock or key.
2. On the key. It would be an engraved or hewn in code.
3. On a metal plate in the glove department or elsewhere in the car.
4. On the lock’s housing.

Why won’t my key turn in my Jeep Grand Cherokee?

What are common reasons my Jeep Grand Cherokee key won’t turn? While there are a variety of reasons your Jeep Grand Cherokee key won’t turn, the most common 3 are a binding steering column/lock, an ignition switch issue, or a problem with the ignition key.

What to do if your Jeep Grand Cherokee wont start?

There are certain emissions-related codes that may require a Chrysler/Jeep dealership to inspect and clear. Disconnect the scan tool from the DTC port when done. If you do not have a quality scan tool, refer to Step 3. Disconnect the negative battery cable and leave it disconnected overnight.

How do you reset a Grand Cherokee computer?

Disconnect the scan tool from the DTC port when done. If you do not have a quality scan tool, refer to Step 3. Disconnect the negative battery cable and leave it disconnected overnight. Reconnect the negative battery cable in the morning and all but any hard codes will be cleared.

When to reset the Immobilizer on a Jeep Grand Cherokee?

The system is activated when something other than an authorized key is used to try to start the engine. Most models are also equipped with an alarm system as part of the security system. If something triggers the immobilizer or the alarm system, you need to reset and rearm the system.

How to reset keyless remote transmitters in Jeep Grand Cherokee?

Climb into your Jeep Grand Cherokee with your keyless remote(s) in hand and your manual ignition key. Do not close the driver’s door. Hit the “Lock” switch on your driver’s side door and insert the key into the ignition. Turn the key to the “Run” position and aim the keyless remote at the steering wheel.